ferrolava.blogg.se - How to setup usb drive tomato

#How to setup usb drive tomato driver#
#How to setup usb drive tomato Pc#
#How to setup usb drive tomato windows 7#
#How to setup usb drive tomato mac#

Now internet originated magic packets will be broadcast to all devices on your network, but only the machines with the correct MAC address within that packet will respond. You’re in business, now go to Port Forwarding and setup a forward for UDP on some high port (5500, 8888, whatever) to internal address 192.168.1.254. 254 dev br0 lladdr ff: ff: ff: ff: ff: ff PERMANENT The solution is to send the magic packet to the broadcast address for your subnet (generally 192.168.1.255) but Tomato won’t allow that, so we work around it by turning 192.168.1.254 into the broadcast address by adding these two lines to server$ ip neigh show 192. The Tomato WoL page lists device status, if it is “Active (In ARP)” then internet WoL commands will work, otherwise no go. This is because it’s address has expired from the ARP cache and you’re boned. You can still login to Tomato and wakeup the computer but that’s it. The hiccup for internet control of WoL is when your computer has been off for 20 minutes or so you won’t be able to send the magic packet from the WAN anymore. Worst case you can always log into your router this way to boot your computer, bypassing the complexity and problems of WAN control as Tomato effectively sends the command from inside your LAN. For easier identification I’ve given all my devices static IPs and names under Basic->Static DHCP. Tomato has built in WoL functions under Tools->WOL where you can click any MAC address listed to send the wakeup command. This will let you log into the web interface or SSH in to a command line for testing or other uses in the future. Configuring Tomato for WoLĪfter you have Tomato (or Tomato USB) installed take a few minutes to secure it for remote access. In Win7 you can change the default shutdown option to hibernate click the Start orb and right click on Shutdown, choose properties, change the Power button action drop-down to Hibernate and click OK.

#How to setup usb drive tomato Pc#

WoL doesn’t always work when the computer is off (depends on the machine), because the network card has no power and thus can’t receive the magic packet, so your PC may have to be in Sleep or Hibernate mode.

#How to setup usb drive tomato driver#

It’s all driver specific so yours could be a variation of those. For me one machine used the property “Wake on Magic Packet” and the value “Enabled”, another used the property “Wake-On-LAN Capabilities” and the value “Pattern Match & Magic Packet”.

#How to setup usb drive tomato windows 7#

On Windows 7 both my machines had WoL enabled by default but to verify you can open your network adapter in Device Manager and check the Advanced tab to see if the property pertaining to WoL is enabled.

Find an iPhone app to send the “magic packet“, which tells your computer to turn onīoth my PCs are somewhat older and don’t have settings labeled “Wake-on-LAN” but instead “Wake-on-PME” (power management event) which is the same thing, enable the option and boot your computer.

Setup DynDNS to always be able to locate my network from the internet.

Configure Linksys router running Tomato USB firmware.

My personal setup required several things: Enable WoL in the computer’s BIOS I don’t need into my computer remotely very often but WoL turned out to be the optimal solution for when I do. For several years I just left my PC on 24/7 to VNC into it anytime, which I stopped doing because it was a massive waste of electricity (i.e. So this article at Lifehacker got me thinking about setting up Wake-on-LAN (WoL) for my system. Plugged it back into the same port on the router that it was in before and it mounted right away.This post is heinously out of date but I'm keeping it around for historical purposes anyway I set the defaults for all the options and chose the non quick format (don't think that matters but that's what I did). From /u/clevernut2's suggestion I took my drive back to my PC and reformatted in FAT32. OK, I had a whole host of variables I was going to independently test from the suggestions given to me, but it worked on my very fist test. So I enabled USB 1.1 but oddly enough the only option available was the OHCI check box.

At first I did not have USB 1.1 enabled, and figured maybe this drive was pre USB 2.0. The router does see the device, but it just doesn't mount it as evident in this screen cap. I have a quite old Corsair Voyager 1GB drive that I just reformatted to NTFS that I plugged into the router. It is my understanding that the mounting process should be just plug and play.

My end goal here is to get my bandwidth logs and maybe even my system logs to log to an external USB thumb drive.

Pardon but my Linux skills are very rusty.